MACDV DASHBOARD

Rev00
- MACDV with momentum
-Still need to optimize and revise many thing.
-Any wrong could you please help feed back , Not much experience.
Description : This dash board create from MACDV Momentum for monitor market cycle with status
Momentum show 6 phase status
C =Previous close price
E1 =EMA50
E2 =EMA200
Phase1 Accumulation = C >E1 >E1 and E1<2: Middle of trend : Buy entry zone
Phase2 Bullish = C >E1 >E2 and E1>E2 : Buy the dip : Buy Exit zone
Phase3 Warning = C<E1 and C>E2 and E1>E2: Trend begin : Sell entry zone
Phase4 Distribution = C<E1 and C<E2 and E1>E2: Middle of trend : Sell entry zone
Phase5 Bearish = C<E1 and C<E2 and E1<E2: Sell the rallies : Sell exit zone
Status show 7
Buy risk = MACDV> 150
Rallying =MACDV>50 and MACDV <150 and MACDV>Signal
Retracing =MACDV>50 and MACDV <150 and MACDV<Signal
Ranging =MACDV<50 and MACDV >-50
Rebounding =MACDV<-50 and MACDV >-150 and MACDV>Signal
Reversing =MACDV<-50 and MACDV >-150 and MACDV<Signal
Sell risk = MACDV<-150
When you monitor form low timeframe status they will change same as standard cycle like sine wave.
Anyway this dash board does not give direct signal for entry buy or sell need to use multiple factor to confluence.
Hope fully you enjoy it, Good luck and Always trade safe.
Phase2 Bullish = C >E1 >E2 and E1>E2 : Buy the dip : Buy Exit zone
Phase3 Warning = C<E1 and C>E2 and E1>E2: Trend begin : Sell entry zone
Phase4 Distribution = C<E1 and C<E2 and E1>E2: Middle of trend : Sell entry zone
Phase5 Bearish = C<E1 and C<E2 and E1<E2: Sell the rallies : Sell exit zone
Phase6 Recovery = C>E1 and C<E2 and E1<E2: Sell the rallies : Sell exit zone
Status show 7
Buy risk = MACDV>150
Rallying =MACDV>50 and MACDV <150 and MACDV>Signal
Retracing =MACDV>50 and MACDV <150 and MACDV-50
Ranging =MACDV>-50 and MACDV<50
Rebounding =MACDV<-50 and MACDV >-150 and MACDV>Signal
Reversing =MACDV<-50 and MACDV >-150 and MACDV<Signal
Sell risk = MACDV<-150
Phase5 Bearish = C<E1 and C<E2 and E1<E2: Sell the rallies : Sell exit zone
Phase6 Recovery = C>E1 and C<E2 and E1<E2: Sell the rallies : Sell exit zone
Status show 7
Buy risk = MACDV>150
Rallying =MACDV>50 and MACDV <150 and MACDV>Signal
Retracing =MACDV>50 and MACDV <150 and MACDV-50
- Enable setting row show/hide
- Color data table
close[1]>close[2] =green, close[1]>close[2]=red
rsi >70 and <30 =red, rsi <70 and >30 =green
ma>ma[1]=green, ma<ma[1]=red
macdv>macv[1]=green, macdv<macdv[1]=red
When used at data lower timeframes than the chart’s, show up incorrect data, This is issue about standard pine scrip function, Need to create special function for keep correct number @ ant timeframe chart.
-For now full dashboard table is useful with lowest timeframe chart in table (Like M5, M15).
-Change decimal to 4 digit
-Close-1Color direction correct
-Momentum data correct
-Regarding "using request.security() at lower timeframes than the chart’s, it is best to avoid using the function at those timeframes" still find out solution then add an option for temporary use
-Setting menu add check box for show only chart timeframe, This table will use only present chart data.
- Multi timeframe table still can use, For default and uncheck box show only chart timeframe, Recommend for correct all table data lowest timeframe(M5), When change to higher timeframe data invalid in low time frame table
- Add table style option in "setting" for more valid data every time frame
- ''Show only chart timeframe'' this check box will show table with single timeframe data without confuse with invalid data from lower than chart timeframe
- "Hide lower timeframe" this check box will show present timeframe with higher timeframe data this option still prevent invalid data from lower than chart timeframe
- Add arrow in MACD-V Momentum
- 🠇 Retracing
- 🠇🠇 Reversing
- 🠅 Rebounding
- 🠅🠅 Rallying
- Remove bias entry word
- Transparent line and border table, setup new default
- This update and sharing form team develop support #Riliza, odilu021
- Clean no use variable
- DX condition cell color
- Remove no use table function
- Default setting update
- Remove no use code
- Add EMA27 line option
- Re-group setting menu.
- Change text TRENDadviser_Diamond to TRENDadvisor_Diamond
- Add arrow status MACD-V momentum = Ranging ⟷
Skrip sumber terbuka
Dalam semangat sebenar TradingView, pencipta skrip ini telah menjadikannya sumber terbuka supaya pedagang dapat menilai dan mengesahkan kefungsiannya. Terima kasih kepada penulis! Walaupun anda boleh menggunakannya secara percuma, ingat bahawa menerbitkan semula kod ini adalah tertakluk kepada Peraturan Dalaman kami.
Untuk akses pantas pada carta, tambah skrip ini kepada kegemaran anda — ketahui lebih lanjut di sini.
Penafian
Skrip sumber terbuka
Dalam semangat sebenar TradingView, pencipta skrip ini telah menjadikannya sumber terbuka supaya pedagang dapat menilai dan mengesahkan kefungsiannya. Terima kasih kepada penulis! Walaupun anda boleh menggunakannya secara percuma, ingat bahawa menerbitkan semula kod ini adalah tertakluk kepada Peraturan Dalaman kami.
Untuk akses pantas pada carta, tambah skrip ini kepada kegemaran anda — ketahui lebih lanjut di sini.